Quatech Device Server Manual do Utilizador Página 93
- Página / 98
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Quatech SDS User’s Manual Appendix A
October 2006 940-0183-154 Page 87
Hardware Processor: Freescale / Motorola Power PC
SDRAM: 8 MB
FLASH Memory: 2 MB
FLASH is field upgradeable over Ethernet connection
Switches
All models: On back panel:
¾ Reset: Resets the unit and does a hard reboot.
User data in volatile memory cleared.
System configuration unchanged.
If held until Status LED flashes slowly and then released:
User data in memory is cleared and configuration is reset to
factory default settings
If held until Status LED flashes quickly and then released:
User data in memory is cleared and system firmware reverts to the
factory default
Indicators
4- and 8-port models: On front panel
¾ Power: On when unit has power
On rear panel
¾ Link (left side of Ethernet connector): Network connection
ON = connected to network; OFF = not connected
¾ Speed (right side of Ethernet connector): Speed of network
connection, ON = 100 Mbps; OFF = 10 Mbps.
¾ Data: Color RED if port is configured for RS-232 operation. Color
GREEN if port is configured for RS-422/485 operation. Flashes
when data is being sent or received on the serial port.
¾ Status: Off until box is running then turned on.
If the Reset button is pushed in and held, the following occurs:
1. Status LED flashes at a rate of 1 flash every 2 seconds for 10
seconds (slow flash).
If Reset button is released during this time period, the
configuration is reset to factory defaults; then the SDS
automatically restarts.
2. If Reset button is held past the first 10 seconds, the LED
starts to flash at a rate of 1 flash per second for 10 seconds
(fast flash).
If Reset button is released during this time period, the SDS is
reset back to factory default firmware revision; then the SDS
automatically restarts.
3. If Reset button is held past the first 20 seconds, the LED
stops flashing.
If Reset button is released during this time period, the SDS
resets but the configuration is unchanged.
- Serial Device Server 1
- User’s Manual 1
- Table of contents 3
- Figures 4
- Introduction 7
- 00:0B:28:12:34:56 8
- Identifying operating modes 9
- System requirements 10
- Features 11
- Wi-Fi implementation 12
- Getting started 13
- Understanding LED codes 15
- 1 2 3 4 5 6 7 8 18
- Making connections 19
- ¾ Address type 27
- ¾ IP Address 27
- ¾ Subnet mask 27
- ¾ Default gateway 27
- Step 28 33
- Step 29 33
- Win NT Device Manager 34
- Uninstalling your SDS 35
- ¾ Find an SDS that is 42
- ¾ Select your SDS model 42
- ¾ Change the SDS’ IP 50
- ¾ Move the SDS to a 50
- ¾ Ignore the problem and 50
- Setting network parameters 53
- Setting SNMP parameters 58
- Preliminary 61
- Step 4 64
- Step 5 64
- Step 4c 70
- Step 4d 70
- Note: In Raw UDP, your SDS 74
- Running diagnostic tests 79
- Checking wireless status 80
- Managing users 81
- Upgrading firmware 84
- Contacting Quatech 85
- Troubleshooting an SDS 86
- ¾ Wrong COM port 88
- ¾ Check COM port in 88
- Maintaining an SDS 89
- Appendix A 90
- Signals: 91
- Switches 93
- Indicators 93
- Certifications FCC, CE, IC 94
- Appendix B 95
- Appendix C 97
Manuais e produtos relacionados com Hardware Quatech Device Server
Hardware Quatech DSP-100 Manual do Utilizador
(57 páginas)
(57 páginas)
Hardware Quatech DSP-200/300 Manual do Utilizador
(52 páginas)
(52 páginas)
Hardware Quatech MPAP-100 Manual do Utilizador
(64 páginas)
(64 páginas)
Hardware Quatech SSCLP-300 Manual do Utilizador
(48 páginas)
(48 páginas)
Hardware Quatech RS-232 Manual do Utilizador
(39 páginas)
(39 páginas)
Hardware Quatech DSCLP-100 Manual do Utilizador
(38 páginas)
(38 páginas)
Hardware Quatech HSU-300 Manual do Utilizador
(55 páginas)
(55 páginas)
Checkline TEM-1 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Czujniki Checkline TEM-1.
Dostarczamy 1 pdf podręczników Checkline TEM-1 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentários a estes Manuais